3If I can't fix it , it must not be broken
wadingriver posted an answer for this 1994 Chevrolet S-10 Blazer:
"Can you hear the fan running when you turn it up? Why would hwy driving make the heat blow..."
wadingriver
wadingriver posted an answer for this 2003 Kia Sorento:
"Sometimes, if there is a strain on the steering wheel, the steering wheel lock will pinch..."
wadingriver
wadingriver posted an answer for this John Deere D130 22HP V-Twin Foot Pedal Hydrostatic 42 Riding Lawn Mower:
"New solenoid, new starter switch. So its not a problem with the high current stater..."
wadingriver
wadingriver posted an answer for this Vacuums:
"Most all run on a rubber belt. They do break. They do slip if roller is clogged"
wadingriver
wadingriver posted an answer for this 2001 Ford Mustang:
"Timing belt/chain. Interference engine, piston is probably hitting the valves"
wadingriver
wadingriver posted an answer for this 1995 Plymouth Neon:
"Possible Intake manifold gasket."
wadingriver
wadingriver posted an answer for this Husqvarna Garden:
"Oh my. All 2 and 4 stroke small engines run up around 120psi. They are tired at sround..."
wadingriver
wadingriver posted a question about Ovens:
"Electric ovens: is there a quality difference when buying replacement burners? I've gone..."
wadingriver
wadingriver posted a question about The Office Equipment & Supplies:
"Parked my TI-83 for years without batteries. Put batteries in and it wouldn't turn on...."
wadingriver
wadingriver posted a question about Miscellaneous:
"OK, the problem was a grounding issue to the actual magnet switch. Enough propane oil..."
wadingriver
wadingriver posted a question about Westinghouse Refrigerators:
"I have a Westinghouse chest freezer. It sat idle for a few years. I plugged it in the..."
wadingriver
wadingriver posted an answer for this Kenmore Sewing Machines:
"Open front nose, it's hinged in the back,
and there is a knob inside. I'm guessing..."
wadingriver
wadingriver posted an answer for this Washing Machines:
"Whats the question? Your statement doesn't make sense. What equipment are you even..."
wadingriver
wadingriver posted an answer for this kawasaki Motorcycles:
"Something was reinstalled incorrectly. You have to be shorting out to Ground."
wadingriverwadingriver posted an answer for this Suzuki Motorcycles:
"Needle valve might be sticking That would cause gas leaking while running and turned off."
wadingriverwadingriver posted an answer for this Suzuki Motorcycles:
"Needle valve might be sticking That would cause gas leaking while running and turned off."
wadingriver
wadingriver posted an answer for this Food Processors:
"Unfortunately these Nutri bullets are expensive garbage. The upper seals do not last and..."
wadingriverwadingriver posted an answer for this Garden:
"Correct size hand file Small saw is likely a 5/32" round file"
wadingriverwadingriver posted an answer for this Kubota Garden:
"Sounds like the new Starter is binding OR engine is seized so it can't crank. Make sure..."
wadingriverwadingriver posted an answer for this Husqvarna Garden:
"You mention new, but how long between uses? Has it been weeks because I'd check for mice..."
wadingriverwadingriver posted an answer for this Garden:
"Does it Crank but not fire or do you not even get a crank? Have you tried jumping a large..."
wadingriver
wadingriver posted an answer for this The Optics:
"Maybe Monstrum lense covers AMAZON"
wadingriver
wadingriver posted an answer for this Heavy Machinery:
"Perhaps clogged hydraulic filters"
wadingriver
wadingriver posted an answer for this Magic Bullet Nutribullet Blender:
"Nutribullet Base is known for seized bearings. Bearing #698RS is the cheap bearings used. ..."
wadingriver
wadingriver posted an answer for this Reddy R155D Utility Heater:
"Make sure fuel tank is venting. Fuel cap gasket might be shifted and blocking vent. Try..."
wadingriver
wadingriver posted an answer for this Dayton E52 Utility Heater:
"Make sure fuel tank is vented. Try keeping fuel cap loose and see if it stays running"
wadingriver
wadingriver posted an answer for this Dayton E50 Heater:
"It's on the label next to the thermostat. 5 or maybe 5.5"
wadingriverwadingriver posted an answer for this Dayton E50 Heater:
"I'd check pump pressure. I think on you unit you have a gauge on the pump. You should..."
wadingriverwadingriver posted an answer for this Dayton Heating & Cooling:
"Late to the show but might help others. Check for cracks in hoses. It sounds like a fuel..."
wadingriverwadingriver posted a question about Maytag Ovens:
"Oven will regulate fine only to 250. It will not finish preheating past that. Changed out..."
wadingriver
Garden 815 answers
Cars & Trucks 267 answers
Dryers 58 answers
Motorcycles 54 answers
Electrical Supplies 47 answers
Boating 27 answers Washing Machines 13 answers
Welding Tools 11 answers
Vacuums 10 answers
Refrigerators 8 answers
